■ Revolutionary 90 degree motherboard mounting from RAVEN RV01
■ Innovative 4.5mm aluminum unibody frame from Temjin TJ07
■ Three 180mm fans for unprecedented positive pressure and stack effect cooling
■ Supports liquid cooling radiator mounting
■ Motherboard back plate opening behind CPU area for quick cooler assembly
■ Supports 11” wide ATX motherboard
■ Foam padded interior for advanced noise absorption
Model No. |
SST-FT02B (black), SST-FT02B-USB3.0 (black) SST-FT02S (silver), SST-FT02S-USB3.0 (silver) SST-FT02B-W (black + window), SST-FT02B-W-USB3.0 (black + window) SST-FT02S-W (silver + window), SST-FT02S-W-USB3.0 (silver + window) |
|
Material | 4.5mm aluminum unibody frame, 0.8mm steel body | |
Motherboard | SSI-CEB, ATX (maximum 12” x 11”), Micro-ATX | |
Drive bay | External | 5.25" x 5 |
-- | ||
Internal | 3.5"/2.5" x 5 , 2.5” x1 | |
Cooling system | Front | -- |
Rear | -- | |
Side | -- | |
Top | 1 x 120mm exhaust, 1200rpm, 19dBA | |
Bottom | 3 x 180mm intake fan 700/1200rpm, 18/34dBA | |
Internal | -- | |
Radiator support | Front | N/A |
Rear | N/A | |
Top | 120mm x 1 | |
Bottom | 120mm x 3 | |
Expansion slot | 7 | |
Front I/O port | USB 2.0 x 2 (SST-FT02B, SST-FT02S, SST-FT02B-W, SST-FT02S-W only) USB 3.0 x 2 (SST-FT02B-USB3.0, SST-FT02S-USB3.0, SST-FT02B-W-USB3.0, SST-FT02S-W-USB3.0 only) Audio x 1 MIC x 1 |
|
Power supply | 1 x Optional standard PS2(ATX) | |
Expansion card | Compatible with 12" (304mm) or 12.2" (309mm) (with fan grille removed), width restriction-6.69" (169mm) | |
Limitation of CPU cooler | 165mm | |
Limitation of PSU | Unlimited | |
Net weight | 15.3kg (FT02B,FT02S) 15kg (FT02B-W, FT02S-W) |
|
Dimension | 212mm (W) x 497mm (H) x 616mm (D), 64.9 liters 8.35" (W) x 19.57" (H) x 24.25" (D), 64.9 liters |
|
Extra | One CP05 included for single hot-swappable SATA hard drive, additional CP05 can be purchased separately |
![]() |
Describe | Ver | Size | Download |
![]() |
v1.0 | 7,146 KB | ![]() |
![]() |
60,225 KB | ![]() |
|
![]() |
686 KB |
![]() |
|
|
As the illustrations above show, most enthusiast motherboards with heat pipes will work fine in the FT02, the heat source is located below other parts of the heat pipe.
CPU cooler:
Horizontal style cooler
Good orientation
Good orientation
Bad orientation
VGA cooler
The illustration here shows a VGA cooler that will not work well in the FT02 because the heat source side (touching the GPU) ends up being located higher than the other end.
1. Use both hands to remove top cover gently.
2. First, loosen two screws located on the top-front cover.
Then push top-front cover in the direction as shown gently and finally pull up to detach the top-front cover.
3. Flip top-front cover over to loosen two screws near front I/O module and detach it gently.
4. Install USB 3.0 front I/O module (part number: G11303260) and fasten two screws back gently.
5. Assemble parts back in reverse order carefully.
Your case is now USB3 ready.