Quiet 120mm fan included for rear exhaust
Dual top panel 120mm fan mounts
All aluminum construction with classic front panel and door design
Die-cast aluminum support for extended cards
Slide-out motherboard tray for Extended-ATX/SSI-EEB motherboards
Dual hard drive compartment with 120mm fan slot in between
PSU slot for ATX/PS2 or redundant PSUs with security holder
Unique SilverStone designed see-through air intake vent with 120mm fan
Home theater component style foot stands
型號
SST-TJ10B (黑), SST-TJ10B-USB3.0 (黑)
SST-TJ10S (銀)
SST-TJ10B-W(黑,透明側窗), SST-TJ10B-W-USB3.0(黑,透明側窗)
SST-TJ10S-W(銀,透明側窗)
材質
前鋁面板門組, 2.0mm 鋁合金架構
主機板
SSI-EEB , Extended ATX , ATX , Micro-ATX
多媒體
--
磁碟架
外露
5.25” x 4
3.5” x 1
隱藏
3.5” x 6
冷卻系統
前方
1 x 120mm 風扇孔
背部
1 x 120mm 風扇(出風), 1200rpm, 21dBA
側方
1 x 120mm中段風扇(進風), 1200rpm, 21dBA
上方
2 x 120mm 風扇孔
底部
--
隱藏
--
擴充槽
7
前置 I/O
USB 2.0 x 2 (SST-TJ10B, SST-TJ10S, SST-TJ10B-W, SST-TJ10S-W only)
USB 3.0 x 2 (SST-TJ10B-USB3.0, SST-TJ10B-W-USB3.0 only) IEEE1394 x 1
audio x 1
MIC x 1
電源
1 x 標準PS2(ATX) 選配 或1 x Redundant PS2
作業系統支援
--
顯示卡
選配(支援12吋顯示卡), width restriction-6.81"
處理器散熱器限高
169mm
電源供應器深度限制
Unlimited
淨重
13 kg
尺寸
207 mm (寬) x 521 mm (高) x 644 mm (深), 69.5 公升
其它
TJ10 NVIDIA Edition
備註
To build your water cooling system, we recommend equip your TJ10 with RADSUPPORT09 to install a 120x2 radiator in TJ10.
NT06-E
Equip your TJ10 with NT06-E for the ultimate combination of quietness and performance.
更多...
FN121-BL
Equip your TJ10 with FN121-BL for added lighting effect in available 120mm fan slots.
更多...
Suscool121
Equip your TJ10 with Suscool121 for the ultimate combination of quietness performance.
更多...
FP35
Add FP35 to an available 3.5" drive bay to enable eSATA and card reader capability.
更多...
SDP08
Use SDP08 to convert an available 3.5" drive bay into two 2.5" drive bays.
更多...
TJ10 manual
v1.0
Q.
USB 3.0線材安裝步驟
A:
1. 將TJ10後方三顆螺絲拆除後,將左側板小心卸除.
2. 使用內六角板手將固定front I/O模組的四顆螺絲卸除,然後將模組小心卸離上蓋.
早期版本的TJ10,請由機殼內側將固定front I/O模組的四顆螺絲卸除,然後將模組小心卸離。
3. 將front I/O模組後方的兩顆螺絲卸除.
4. 將front I/O模組左右兩邊共兩顆螺絲卸除.
5. 卸除固定USB模組的四顆螺絲,然後將舊模組小心地卸除.
6. 安裝新的USB 3.0 模組(零件料號: G11303500),並將四顆固定螺絲小心地鎖上.
7. 安裝新的front I/O鋁上蓋(零件料號: 銀色: G10106112 / 黑色: G10106122),然後將左右共兩顆螺絲小心地鎖上。
再依相反的步驟,將機殼小心地裝回. 您的機殼現在已經升級至USB 3.0.
如有任何問題, 請洽服務與支援信箱 :support@silverstonetek.com 。